Weighing The Benefits Of Plasma Metal Cutting Technology Over Oxyfuel In Manual Cutting Applications : search results

... fit MicroSteps bevel systems similarly to HiFocus . The new Smart Focus range was designed particularly for Dollar-Markets and ... ... operation and after sales and standardized components. Its manual and autogas boxes as well as Smart Focus torch heads PerCut 4000 are used in all models – which greatly improves stocking and after sales ... ... systems use well-proven technologies Contour Cut and Contour Cut ...

read more

In oxyfuel cutting, oxygen is used as the cutting gas. Cutting is initiated by heating the edge of the steel to the ignition temperature, and then torch blows extra oxygen at higher pressures into the workpiece. The chemical reaction releases large amounts of energy causing the metal to burn and blowing the resulting molten oxide through to the other side. The oxygen chemically combines ...

read more

MicroStep cutting tables prove to have excellent exhausting efficiency achieved through division of the cutting table into suction zones with electronically controlled opening/closing according to the position of the tool station with active technology. This fully automated system, in connection with high efficiency filter units from renowned world producers, is designed to meet the standards ...

read more

Plasma is an electrically conductive gas.  The ionization of gases causes the creation of free electrons and positive ions among the gas atoms. When this occurs, the gas becomes electrically conductive with current carrying capabilities. Thus, it becomes a plasma.   Plasma cutting is a process that utilizes an optimized nozzle orifice to constrict a very ... ... so ...

read more

Rotator torch holder with automatic calibration The auto-calibration system of tool geometry – ACTG – brings improved accuracy for a long-term continuous performance of bevel tool stations. The self-learning calibration system is a smart solution that detects and ... ... which can arise during collisions or other outer manipulations with the torch. Along with the new ITH solution, MicroStep has ...

read more

Rotator torch holder with automatic calibration The auto-calibration system of tool geometry – ACTG – brings improved accuracy for a long-term continuous performance of bevel tool stations. The self-learning calibration system is a smart solution that detects and ... ... which can arise during collisions or other outer manipulations with the torch. Along with the new ITH solution, MicroStep has ...

read more

For Champions in Sheet Metal Working Comprehensive cutting solutions Technologies: ABP / make additional weld edge preparations on ... ... Bevel™ technology) ITH + ACTG / achieve accurate bevelling results in long-term operation Machines: *NEW* MG / redesigned and full of technologyplasma rotator, ABP, ABC, ACTG, drilling, pipe & profile cutting *NEW* ProfileCut / CNC machine with 3D ...

read more

Thank you for visiting our website for your CNC cutting machine and related accessories, technology and software ultimate selection Your browser does not support the video tag. The company MicroStep, spol. s r. o. manufactures and supplies CNC machines equipped with plasma, fiber laser, oxyfuel, waterjet and routing technologies. Besides machine ... ... machine tools and CAM software with ...

read more

... MPM from MicroStep integrates production and storage with control systems of the CNC machines and software for creation of cutting plans AsperWin and mCAM. The company MicroStep, spol s. r. o. , is a renowned Slovak producer of CNC machines used for cutting material using a wide spectrum of technologies (plasma, laser, oxyfuel, waterjet). Furthermore, MicroStep machines ... ... functions ...

read more

It is with great pride that we announce the foundation of a new MicroStep subsidiary Microstep USA that took place in October 2016. Based in Gastonia, North Carolina, our newest branch ... ... year, MicroStep made a big and important step over the Atlantic Ocean to bring its drive for innovation to the United States of America. It is with great pride that we announce the foundation of a new MicroStep ...

read more

True surface representation with mSCAN Production of pressure vessels and boilers counts among the major industrial applications where cutting of 3D objects comprises an essential part of the production process. The obvious requirement is to make this process fast, ... ... an accurate result that won´t need further mechanical or even manual processing. Typical cutting tasks in this regard are cutting ...

read more

Waterjet cutting involves passing water under high pressure through a small diameter nozzle to produce a waterjet. The jet travels at a very high speed, with sufficient kinetic energy to cut a wide range of materials. If sand is added, an abrasive affect occurs that allows the waterjet to cut hard materials such as metal and stone. Our partners for waterjet cutting: Accustream ... .... thyssenkrupp ...

read more

... ever MicroStep´s flagship MG redesigned and more powerful than ever The machine has it all: a high-end design with a long tradition in the field counting hundreds of successful installations, outstanding dynamics and precision, a great variety of equipment to choose from with dozens of functions. For the moment it is the most popular MicroStep machine and it gets all the attention it deserves ...

read more

Laser cutting works by focusing the power of a high-power laser onto the surface of the material to be cut. The energy in the laser beam is absorbed into the surface of material, and the energy of the laser is converted into heat, which melts or vaporizes the material. Additionally, gas is focused or blown into the cutting region to expel or blow away the molten metal and vapor from ...

read more

1991   founding of MicroStep, spol. s r. o. by 10 employees of the Department of Control  and  Automation, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology in Bratislava    initial company goal – to develop and deliver microprocessor-based control technology to various branches of industry   ...

read more

.... 2 nd Symposium on Innovation, Cooperation in Technology and International Transfer of Technology China + 16 CEEC Format was held on 20. – 23. 9. 2015 in four Slovak cities – Bratislava, Žilina, Trenčín and Nitra. The international event was hosted by the Ministry of Foreign and European Affairs of the Slovak Republic, Ministry of Education, Science, Research and Sport of ...

read more

Material-flow system for automatic sheet-metal cutting installation Demag process crane serves six CNC plasma cutting systems Crane control system and WMS provide for continuous utilisation of the machinery Wetter, Germany - The installation of a fully automated plate metal processing facility has enabled a Chinese manufacturer of mining equipment to increase productivity in its production facility ...

read more

3D cutting solutions for steel constructions 3D cutting solutions for steel constructions Apart from standard flat-bed machines, MicroStep offers an exceptional variety of equipment for processing of 3D rotary objects and structural steel sections of various shapes. The rotary objects include differently sized circular, square and rectangular hollow sections (diameters of circular sections reach ...

read more

© copyright 1991-2017 MicroStep, spol. s r.o. | developed by EXPLORE STUDIOS